Abstract：[Objective] Currently, iron or steel brake disks generally be selected to research braking noise. This research focuses mainly on the influence of the structural characteristics of the brake pads and brake disks on the braking noise, and few studies addresse how braking conditions or braking modes affect the noise characteristics. To clarify the causes of the abnormal noise in the braking process of different friction pairs, through a noise test of the multiscale bench braking test and the simulation method of complex eigenvalue analysis, this paper studys the braking noise characteristics and the generating mechanism of different friction pairs under different braking conditions and braking modes. [Methods] According to the scaled test scheme, a scaled test of three types of friction pairs is performed on the MM-1000/IV scaled test machine, and the braking noise characteristics of the friction pairs are compared and analyzed. For the selected friction pair of the SiCp/A356 composite brake disk and synthetic pad, a more realistic 1∶1 bench brake test is performed. On the basis of HyperMesh and Abaqus software, a finite element simulation model of the wheel-mounted disk foundation braking device with a wheel, disks, pads, pad holders, brake levers, etc. is constructed. [Results] Under the same working conditions, the sound pressure levels (SPL) of the two SiCp/A356 composite friction pairs were lower than those of FE-928W friction pair. The maximum value of maximum sound pressure level (Max SPL) was 96 dB for the FE-928W friction pair and 87 dB for the BJTU-928W friction pair. The braking noise type of the FE-928W friction pair was mainly a multifrequency squeal, and the braking squealing phenomenon occured in most working conditions. The noise types of the BJTU-928W friction pair and the KNORR-928W friction pair were mainly wide area noise and single frequency squeal. The friction surfaces of different friction pairs had different degrees of surface scratching, material transfer, and peeling, which led to differences in the braking noise. The main frequency of the squealing noise of the friction pair between the SiCp/A356 composite brake disk and the synthetic brake pad was concentrated near 2.20 kHz, and the Max SPL could reach 110 dB. Brake pads were the main source of braking noise. The greater the energy inputed, the more times of high-temperature continuous braking, the greater the squealing sound pressure level, and the more severe the squeal. In contrast, when braking at a lower energy input level, the disk state would be restored, and quiet braking could be achieved during subsequent braking. [Conclusions] Through the experiments and simulations, the simulation method of complex eigenvalue analysis can better predict the tendency of braking noise, and the braking noise characteristics and causes of different friction pairs under different braking conditions and braking modes are clarified. This research provides a scientific basis for noise reduction strategies such as friction matching, structural design optimization, and braking mode improvement of the friction pair between the SiCp/A356 composite brake disk and the synthetic brake pad.
杨智勇, 王子鸣, 叶珊珊, 李志强, 李卫京. 基于多尺度制动试验的制动噪声特性及仿真分析方法[J]. 清华大学学报（自然科学版）, 2023, 63(10): 1626-1639.
YANG Zhiyong, WANG Ziming, YE Shanshan, LI Zhiqiang, LI Weijing. Braking noise characteristics and a simulation analysis method based on a multiscale braking test. Journal of Tsinghua University(Science and Technology), 2023, 63(10): 1626-1639.
[1] 陈光雄.金属往复滑动摩擦噪声的研究[D].成都:西南交通大学, 2002. CHEN G X. Investigation into friction-induced noise under metal reciprocating sliding conditions[D]. Chengdu:Southwest Jiaotong University, 2002.(in Chinese) [2] AKAY A. Acoustics of friction[J]. The Journal of the Acoustical Society of America, 2002, 111(4):1525-1548. [3] 张雪刚,王书文,张欢,等.摩擦制动低频振动噪声的研究现状[J].噪声与振动控制, 2018, 38(S1):233-238. ZHANG X G, WANG S W, ZHANG H, et al.A review on frictional braking low-frequency noise and vibrations[J].Noise and Vibration Control, 2018, 38(S1):233-238.(in Chinese) [4] 代立宏,李虎本,黄巨成,等.特定工况固定频率制动噪音解决方案研究[J].智能制造, 2019(6):57-61. DAI L H, LI H B, HUANG J C, et al. Research on the solution of fixed frequency braking noise in specific working conditions[J]. Intelligent Manufacturing, 2019(6):57-61.(in Chinese) [5] 张骏.基于缩比试验的热斑研究[D].北京:北京交通大学, 2012. ZHANG J. Research of hot spot based on scaling test[D]. Beijing:Beijing Jiaotong University, 2012.(in Chinese) [6] 赵小楼.摩擦材料缩比试验原理及试验方法和测试设备研究[D].长春:吉林大学, 2007. ZHAO X L. Study on the principle and test method of the scaling test of the friction material and its equipment[D]. Changchun:Jilin University, 2007.(in Chinese) [7] 邓小军.高速列车车内噪声预测与控制技术研究[D].北京:北京交通大学, 2017. DENG X J. Research on interior noise prediction and control technology of high speed train[D]. Beijing:Beijing Jiaotong University, 2017.(in Chinese) [8] BAJER A, BELSKY V, ZENG L J. Combining a nonlinear static analysis and complex eigenvalue extraction in brake squeal simulation[C]//Proceedings of the 21st Annual Brake Colloquium&Exhibition. Hollywood, USA:SAE International, 2003:2003-01-3349. [9] WU Y K, TANG B, XIANG Z Y, et al. Brake squeal of a high-speed train for different friction block configurations[J]. Applied Acoustics, 2021, 171:107540. [10] 张康智,毕永强.高速列车盘形制动系统摩擦振动行为动力学分析[J].机械科学与技术, 2020, 39(2):228-234. ZHANG K Z, BI Y Q. Finite element analysis on friction vibration behavior of high-speed train disc braking system[J]. Mechanical Science and Technology for Aerospace Engineering, 2020, 39(2):228-234.(in Chinese) [11] 全鑫,莫继良,王安宇,等.高速列车制动片摩擦块尺寸对制动噪声特性的影响[J].润滑与密封, 2019, 44(9):50-55. QUAN X, MO J L, WANG A Y, et al. Effect of friction block size of high-speed train brakes on noise characteristics[J]. Lubrication Engineering, 2019, 44(9):50-55.(in Chinese) [12] 全鑫.高速列车制动片摩擦块形状及尺寸对制动噪声特性的影响[D].成都:西南交通大学, 2019. QUAN X. The influence of friction block shape and size of high-speed train brakes on brake noise characteristics[D]. Chengdu:Southwest Jiaotong University, 2019.(in Chinese) [13] 杨自帅. CRH5制动噪声有限元分析[D].大连:大连交通大学, 2016. YANG Z S. Finite element analysis of brake noise on CRH5[D]. Dalian:Dalian Jiaotong University, 2016.(in Chinese) [14] 李建熹.盘式制动尖叫噪声及制动片界面修饰降噪研究[D].成都:西南交通大学, 2017. LI J X. Study on the disc brake squeal noise and the improvement of noise performance by modifying the characteristics of pad surface[D]. Chengdu:Southwest Jiaotong University, 2017.(in Chinese) [15] OBERST S, LAI J C S, MARBURG S. Guidelines for numerical vibration and acoustic analysis of disc brake squeal using simple models of brake systems[J]. Journal of Sound and Vibration, 2013, 332(9):2284-2299. [16] 郑涛.基于复模态分析的盘式制动器仿真优化[D].杭州:浙江大学, 2018. ZHENG T. Simulation optimization of disc brake based on complex modal analysis[D]. Hangzhou:Zhejiang University, 2018.(in Chinese) [17] 盖小红.沟槽型表面织构抑制列车盘形制动尖叫噪声的研究[D].成都:西南交通大学, 2016. GAI X H. The study of suppressing railway disc brake squeal noise by grooved surface texturing[D]. Chengdu:Southwest Jiaotong University, 2016.(in Chinese) [18] 阳江舟.沟槽型织构化表面对制动盘/片材料摩擦尖叫噪声的影响[D].成都:西南交通大学, 2015. YANG J Z. The effects of groove-textured surfaces on friction-induced squeal noise of brake disc/pad materials[D]. Chengdu:Southwest Jiaotong University, 2015.(in Chinese) [19] 王晓翠.沟槽型织构化表面对摩擦振动噪声影响的试验及有限元分析[D].成都:西南交通大学, 2015. WANG X C. The experimental and numerical study of the effect of groove-textured surface on the friction-induced vibration and noise[D]. Chengdu:Southwest Jiaotong University, 2015.(in Chinese) [20] WANG D W, MO J L, LIU M Q, et al. Improving tribological behaviours and noise performance of railway disc brake by grooved surface texturing[J]. Wear, 2017, 376-377:1586-1600. [21] KARAMOOZIAN A, TAN C A, WANG L M. Squeal analysis of thin-walled lattice brake disc structure[J]. Materials&Design, 2018, 149:1-14. [22] 张振华.盘式制动器制动噪声影响因素分析与改进[D].重庆:重庆理工大学, 2021. ZHANG Z H. Analysis of influencing factors and improvement of braking noise of disc brake[D]. Chongqing:Chongqing University of Technology, 2021.(in Chinese) [23] 黄盼盼.轮盘制动尖叫噪声的研究[D].成都:西南交通大学, 2014. HUANG P P. Finite element analysis of the squeal propersity for a wheel-disc brake system[D]. Chengdu:Southwest Jiaotong University, 2014.(in Chinese) [24] KHARATE N K, CHAUDHARI S S. Effect of material properties on disc brake squeal and performance using FEM and EMA Approach[J]. Materials Today:Proceedings, 2018, 5(2):4986-4994. [25] BERGMAN F, ERIKSSON M, JACOBSON S. The effect of reduced contact area on the occurrence of disc brake squeals for an automotive brake pad[J]. Proceedings of the Institution of Mechanical Engineers, Part D:Journal of Automobile Engineering, 2000, 214(5):561-568. [26] LIU P, ZHENG H, CAI C, et al. Analysis of disc brake squeal using the complex eigenvalue method[J]. Applied Acoustics, 2007, 68(6):603-615. [27] CHEN G X, LÜ J Z, ZHU Q, et al. Effect of the braking pressure variation on disc brake squeal of a railway vehicle:Test measurement and finite element analysis[J]. Wear, 2019, 426-427:1788-1796. [28] 吕辉,于德介,陈宁,等.引入不确定参数的汽车盘式制动器振动稳定性分析[J].振动工程学报, 2014, 27(6):900-906. LÜ H, YU D J, CHEN N, et al. Analysis of automotive disc brake systems vibration stability by introducing uncertain parameters[J]. Journal of Vibration Engineering, 2014, 27(6):900-906.(in Chinese) [29] YANG Z Y, WANG Z M, WANG J L, et al. Tribological properties of SiCp/A356 composites against semimetallic materials under dry and wet conditions[J]. Journal of Materials Engineering and Performance, 2021, 30(6):4148-4161. [30] 中华人民共和国国家质量监督检验检疫总局,中国国家标准化管理委员会.电声学声校准器:GB/T 15173-2010[S].北京:中国标准出版社, 2010. General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China. Electroacoustics-sound calibrators:GB/T 15173-2010[S]. Beijing:Standards Press of China, 2010.(in Chinese) [31] 王佳琳.服役环境下SiCp/A356复合材料摩擦第三体演变行为研究[D].北京:北京交通大学, 2018. WANG J L. Research on the evolution behavior of third-body layer on the surface of SiCp/A356 composites under service environment[D]. Beijing:Beijing Jiaotong University, 2018.(in Chinese) [32] 国家市场监督管理总局,中国国家标准化管理委员会.公共场所卫生指标及限值要求:GB 37488-2019[S].北京:中国标准出版社, 2019. General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China. Hygienic indicators and limits for public places:GB 37488-2019[S]. Beijing:Standards Press of China, 2019.(in Chinese)
2023, Vol. 63 
