Abstract：The effects of a power loss to the engine front end accessory belt drive systems were studied using a multi-body dynamic simulation. The mechanical parameters of the belt were found in tests with the system dynamic model then built in the commercial software Adams. The effects of the system power loss were found through a series of simulations for the key design parameters, such as the belt pre-tension, accessory loads, rotating speed belt and pulley acceleration, and fuel consumption, for typical vehicle driving cycles. The results show that the power loss increases monotonically with pre-tension, load and rotating speed and changes little with acceleration. The fuel consumption agrees well with bench tests of a drive system without any accessory loads.
陶润, 侯之超. 发动机前端附件带传动系统功率损失的仿真分析[J]. 清华大学学报（自然科学版）, 2015, 55(7): 790-796.
TAO Run, HOU Zhichao. Simulation on power loss of engine front end accessory belt drive systems. Journal of Tsinghua University(Science and Technology), 2015, 55(7): 790-796.
[1] Gerbert B G. Power loss and optimum tensioning of V-belt drives [J]. Journal of Engineering for Industry: Transactions of ASME, 1974, 96(3): 877-885.
[2] Townsend W T, Salisbury J K. The efficiency limit of belt and cable drives [J]. Journal of Mechanisms Transmissions and Automation Design: Transactions of the ASME, 1988, 110(3): 303-307.
[3] Childs T H, Parker J E. Power transmission by flat, V and timing belt [J]. Tribological Design of Machine Elements, 1989, 15(14): 133-142.
[4] Peeken H, Fischer F. Experimental investigation of power loss and operating conditions of statically loaded belt drive [C]//Proceedings of the 1989 International Power Transmission Gearing Conference. Chicago, IL, USA: American Society of Mechanical Engineers, 1989: 15-24.
[5] Forth T, Antchak J, Fought M, et al. Optimized Engine Accessory Drive Resulting in Vehicle FE Improvement [R]. SAE 2008-01-2761, 2008.
[6] Santos L C D, Stief H, Vogelgesang F. Investigations on Friction Losses within Front End Accessory Drives [R]. SAE 2010-36-0178, 2010.
[7] Barker C R, Oliver L R, Breig W F. Dynamic Analysis of Belt Drive Tension Forces during Rapid Engine Acceleration [R]. SAE 910687, 1991.
[8] Takagishi H, Yoneguchi H, Sopouch M, et al. Simulation of Belt System Dynamics Using a Multi-Body Approach: Applications to Synchronous Belts and V-Ribbed-Belts [EB/OL]. [2014-08-20]. http://wenku.baidu.com/link?url=KEiU4G1IBL5oZ-JNNDIUKW5Sr6xzJgKCL4GDo1e R92gBLU0R8-r6uAZD9s2ckluf5-dgtA0hYvPFDub-RTKzEO-98SNpCNWB1yv6ujoOlqK.
[9] Zhu H. Finite element modal analysis of the engine front end accessory drive systems [J]. Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, 1994, 208(1): 49-53.
[10] Mashhadi B, Zakeri E. Dynamical analysis and design of front engine accessory drive system [J]. International Journal of Automotive Engineering, 2011, 1(1): 38-46.
[11] 刘元冬, 王文林, 罗明军. 基于Adams发动机前端附件带传动的动态特性研究[J]. 机械传动, 2013, 37(6): 28-32.LIU Yuandong, WANG Wenlin, LUO Mingjun. Research on dynamic characteristic of belt drive system of engine front end accessory based on Adams [J].Journal of Mechanical Transmission, 2013, 37(6): 28-32. (in Chinese)
[12] Cepon G, Manin L, Boltezar M. Introduction of damping into the flexible multibody belt drive model: A numerical of experimental investigation [J]. Journal of Sound and Vibration, 2009, 324(2): 283-296.
[13] Cepon G, Manin L, Boltezar M. Experimental identification of the contact parameters between a V ribbed belt and pulley [J].Mechanism and Machine Theory, 2010, 45(10): 1424-1433.
[14] Cepon G, Boltezar M. An Advanced Numerical Model for Dynamic Simulations of Automotive Belt-Drives [R]. SAE 2010-01-1409, 2010.
[15] GB 18352.3—2005.轻型汽车污染物排放限值及测量方法 [S]. 北京: 中国人民共和国国家环境保护总局, 国家质量监督检验检疫总局, 2005.GB 18352.3—2005. Limits and Measurement Methods for Emissions from Light-Duty Vehicles [S]. Beijing: State Environmental Protection Administration, State Administration of Quality Supervision, Inspection and Quarantine, People's Republic of China, 2005. (in Chinese)
2015, Vol. 55 
