Residual stresses after on-line surfacing welding repairs on the flange surface of a nuclear grade pipe end
LU Li1,2,5, HU Mengjia1, CAI Zhipeng1,2,3, LI Kejian1, WU Yao4, PAN Jiluan1
1. Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China; 2. State Key Laboratory of Tribology, Tsinghua University, Beijing 100084, China; 3. Collaborative Innovation Center of Advanced Nuclear Energy Technology, Beijing 100084, China; 4. Tsinghua University Research Institute for Advanced Equipment, Tianjin 300304, China; 5. Suzhou Nuclear Power Research Institute, Suzhou 215004, China
Abstract：Numerical simulations were used to study the effect of welding sequence and surfacing thickness on the residual stresses and deformation after on-line surfacing welding repair of the flange surface of a nuclear grade pipe. The simulations show that the welding sequence from the inside to the outside wall leads to smaller residual stresses and deformation due to the different thicknesses of the inside and outside walls of the flange and the rigidity differences between the connecting pipes. With a 20 mm surfacing thickness, the residual axial stress at the welding seam of the outer pipe wall is close to the material yield strength. With surfacing thicknesses no more than 15 mm thick, the residual stress at the welding seam of the outer pipe wall is far lower than the yield strength. A sample specimen was made using the optimized welding process with the residual stress then measured using X-ray diffraction. The predicted stresses agree well with the measured data to verify the simulation results.
鲁立, 胡梦佳, 蔡志鹏, 李克俭, 吴瑶, 潘际銮. 核级管端法兰面在线堆焊修复的残余应力[J]. 清华大学学报（自然科学版）, 2020, 60(1): 89-94.
LU Li, HU Mengjia, CAI Zhipeng, LI Kejian, WU Yao, PAN Jiluan. Residual stresses after on-line surfacing welding repairs on the flange surface of a nuclear grade pipe end. Journal of Tsinghua University(Science and Technology), 2020, 60(1): 89-94.
[1] SHALABY H M. Failure investigation of 321 stainless steel pipe to flange weld joint[J]. Engineering Failure Analysis, 2017, 80:290-298. [2] COULES H E, SMITH D J. Measurement of the residual stresses in a PWR control rod drive mechanism nozzle[J]. Nuclear Engineering & Design, 2018, 333:16-24. [3] ALORAIER A, AL-MAZROUEE A, PRICE J W H, et al. Weld repair practices without post weld heat treatment for ferritic alloys and their consequences on residual stresses:A review[J]. International Journal of Pressure Vessels & Piping, 2010, 87(4):127-133. [4] SATTARI-FAR I, JAVADI Y. Influence of welding sequence on welding distortions in pipes[J]. International Journal of Pressure Vessels & Piping, 2008, 85(4):265-274. [5] DENG D, MURAKAWA H, LIANG W. Numerical simulation of welding distortion in large structures[J]. Computer Methods in Applied Mechanics & Engineering, 2007, 196(45):4613-4627. [6] JIANG W, LIU Z, GONG J M, et al. Numerical simulation to study the effect of repair width on residual stresses of a stainless steel clad plate[J]. International Journal of Pressure Vessels & Piping, 2010, 87(8):457-463. [7] SCHAUPP T, SCHOEPFER D, KROMM A, et al. Welding residual stresses in 960 MPa grade QT and TMCP high-strength steels[J]. Journal of Manufacturing Processes, 2017, 27:226-232. [8] DONG P, HONG J K, BOUCHARD P J. Analysis of residual stresses at weld repairs[J]. International Journal of Pressure Vessels & Piping, 2005, 82(4):258-269. [9] ZHANG T, BRUST B, WILKOWSKI G, et al. Weld residual stress analysis and the effects of structural overlay on various nuclear power plant nozzles[J]. Journal of Pressure Vessel Technology, 2012, 134(6):061205. [10] SONG T K, KIM Y B, KIM Y J, et al. Prediction of welding residual stress profile in dissimilar metal nozzle butt weld of nuclear power plant[J]. Procedia Materials Science, 2014, 3:784-789. [11] WOO W, EM V, HUBBARD C R, et al. Residual stress determination in a dissimilar weld overlay pipe by neutron diffraction[J]. Materials Science & Engineering A, 2011, 528(27):8021-8027. [12] LIU R F, HUANG C C. Welding residual stress analysis for weld overlay on a BWR feedwater nozzle[J]. Nuclear Engineering & Design, 2013, 256:291-303. [13] 任维嘉, 吴爱萍, 赵海燕, 等. 大型电机转子焊接残余应力的数值分析[J]. 焊接学报, 2002, 23(4):92-96. REN J W, WU A P, ZHAO H Y, et al. Finite element method analysis on welding residual stresses of large electromotor rotor[J]. Transactions of the China Welding Institution, 2002, 23(4):92-96. (in Chinese)
2020, Vol. 60 
