Preparation and process optimization of C/C composites based on the multi-channel flow field and thermal field control
HUANG Xiaoqing1, WANG Pengfei2, ZHANG Song3, ZHANG Hui1
1. Department of Engineering Physics, Tsinghua University, Beijing 100084, China; 2. Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050, China; 3. Institute for Aero Engine, Tsinghua University, Beijing 100084, China
Abstract：[WTBZ] ［Objective］ Fiber-reinforced composite materials are widely used in aerospace due to high-temperature resistance and high specific strength. The popular chemical vapor infiltration (CVI) method slowly penetrates the porous preform through a gas source and decomposes the carbon source gas into pyrolytic carbon for deposition. This method offers the advantages of less fiber damage and designability of special-shaped components; however, the CVI preparation cycle is long, and the pore blockage on the fiber preform surface makes the densification of the porous preform uneven. To effectively improve the controllability and uniformity of the deposition of porous composite materials, a dual-process chemical vapor infiltration/deposition (CVI/CVD) system bases on a dual-temperature zone-dual-channel structure is proposed in this study, with strong designability and manufacturability and an improved CVI. ［Methods］ Bases on the influence of gas flow direction and temperature on the deposition process, CVD is introduced to combine the two parameters, thus improving the densification uniformity while shortening the fabrication cycle. Since the complex transport and reaction of carbon source and carrier gases is a multivariate multi-coupling process with a great impact on the deposition efficiency and uniformity, numerous modeling and experimental studies are required. In this paper, the process design and system optimization are conducted to generate carbon/carbon composites (C/C composite) bases on the integrated research idea of equipment design-build- theory-preparation-optimization. By establishing flow, heat transfer, and mass transfer reaction models, the effects of temperature, velocity, and concentration on the densification process are analyzed. The two-step deposition simulation of the porous composites is conducted via the dual-process CVI/CVD system. ［Results］ The results showed that reducing the deposition temperature could reduce the deposition rate, avoid saturated adsorption on the preform surface before complete deposition, and improve the deposition uniformity in the thickness direction. Increasing the temperature to increase the reaction rate could easily lead to surface deposition, causing the surface pores to close and block, thus hindering further deposition. The deposition position could be controlled by changing the spatial temperature gradient. For the same temperature gradient, the higher the control temperature, the larger the main deposition area; for a higher control temperature, the main deposition area decreased with the increasing temperature gradient. When the time for the reaction carbon source gas and the carrier gas to be transported to the deposition area was equal to that for the deposition reaction to consume the atmosphere source, the initial velocity matched the concentration, improving the densification efficiency. The two-step deposition simulation results showed that the porous preforms achieved a relatively uniform density in horizontal and vertical directions after the two-step CVI/CVD. ［Conclusions］ By combining the two processes, a dual-temperature zone-dual-channel CVI/CVD system is constructed. A mathematical and a physical model of densification are established, based on the basic theories of chemical reaction kinetics and heat and mass transfer to perform the variable parameter simulation experiment. The flow and thermal field control process optimization design is performed for the prepared C/C composite material, verifying the feasibility of the uniformity control and the process optimization of the C/C composite material deposition sample and providing significant guidance to conduct the future experiments.
黄晓青, 王鹏飞, 张松, 张辉. 基于多通道流场与热场控制的C/C复合材料制备与工艺优化[J]. 清华大学学报（自然科学版）, 2023, 63(10): 1658-1671.
HUANG Xiaoqing, WANG Pengfei, ZHANG Song, ZHANG Hui. Preparation and process optimization of C/C composites based on the multi-channel flow field and thermal field control. Journal of Tsinghua University(Science and Technology), 2023, 63(10): 1658-1671.
[1] SUN C, LI H J, FU Q G, et al. Double SiC coating on carbon/carbon composites against oxidation by a two-step method[J]. Transactions of Nonferrous Metals Society of China, 2013, 23(7):2107-2112. [2] 何子博,李贺军,史小红,等. LPCVD法制备SiC-MoSi2涂层的形貌及沉积机理研究[J].材料导报, 2012, 26(20):1-5. HE Z B, LI H J, SHI X H, et al. Study on the morphology and deposition mechanism of SiC-MoSi2 coating deposited by LPCVD[J]. Materials Review, 2012, 26(20):1-5.(in Chinese) [3] 张守阳,李贺军,孙军. LTCVI工艺中的致密化效率研究[J].材料工程, 2001(9):44-46. ZHANG S Y, LI H J, SUN J. An investigation on the densification efficiency of LTCVI[J]. Journal of Materials Engineering, 2001(9):44-46.(in Chinese) [4] HE Z, LI H, SHI X, et al. Formation mechanism and oxidation behavior of MoSi2-SiC protective coating prepared by chemical vapor infiltration/reaction[J]. Transactions of Nonferrous Metals Society of China, 2013, 23(7):2100-2106. [5] 解静,李克智,付前刚,等.聚合物浸渍裂解法制备C/C-ZrC-SiC-ZrB2复合材料及其性能研究[J].无机材料学报, 2013, 28(6):605-610. XIE J, LI K Z, FU Q G, et al. Preparation and properties of C/C-ZrC-SiC-ZrB2 composites via polymer infiltration and pyrolysis[J]. Journal of Inorganic Materials, 2013, 28(6):605-610.(in Chinese) [6] 李伟,张守阳,李贺军,等.正丁醇等温CVI工艺制备C/C复合材料[J].固体火箭技术, 2010, 33(6):694-697. LI W, ZHANG S Y, LI H J, et al. Preparation of C/C composites using n-butyl alcohol[J]. Journal of Solid Rocket Technology, 2010, 33(6):694-697.(in Chinese) [7] VAIDYARAMAN S, LACKEY W J, AGRAWAL P K, et al. Carbon/carbon processing by forced flow-thermal gradient chemical vapor infiltration using propylene[J]. Carbon, 1996, 34(3):347-362. [8] VAIDYARAMAN S, JACK LACKEY W, FREEMAN G B, et al. Fabrication of carbon-carbon composites by forced flow-thermal gradient chemical vapor infiltration[J]. Journal of Materials Research, 1995, 10(6):1469-1477. [9] BESMANN T M, LOWDEN R A, STINTON D P, et al. A method for rapid chemical vapor infiltration of ceramic composites[J]. Journal de Physique Colloques, 1989, 50(C5):C5-229-C5-239. [10] BESMANN T M, MCLAUGHLIN J C, LIN H. Fabrication of ceramic composites:Forced CVI[J]. Journal of Nuclear Materials, 1995, 219:31-35. [11] XIE J, LI K Z, LI H J, et al. Ablation behavior and mechanism of C/C-ZrC-SiC composites under an oxyacetylene torch at 3000℃[J]. Ceramics International, 2013, 39(4):4171-4178. [12] ZHANG J X, CHENG L F, LIU Y S, et al. Fabricating thick-section carbon fiber/silicon carbide composites by machining-aided chemical vapor infiltration[J]. Ceramics International, 2017, 43(16):13276-13281. [13] WANG Y G, ZHU X J, ZHANG L T, et al. Reaction kinetics and ablation properties of C/C-ZrC composites fabricated by reactive melt infiltration[J]. Ceramics International, 2011, 37(4):1277-1283. [14] 汤中华.用定向流动热梯度CVI工艺制备航空刹车用C/C复合材料的研究[D].长沙:中南大学, 2003. TANG Z H. Research on the fabrication of C/C composites used as aircraft disk brakes by the directional flow thermal gradient CVI process[D]. Changsha:Central South University, 2003.(in Chinese) [15] 邹志强,汤中华,熊杰.用热梯度式CVD增密技术制造C/C复合刹车盘[J].新型炭材料, 2000, 15(2):22-27. ZOU Z Q, TANG Z H, XIONG J. The manufacturing of C/C composite brake disk by means of thermal gradient CVD densification technique[J]. New Carbon Materials, 2000, 15(2):22-27.(in Chinese) [16] GOLECKI I, MORRIS R, NARASIMHAN D. Method of rapidly densifying a porous structure:EP-US5348774 A[P]. 1993-08-11. [17] GOLECKI I, MORRIS R C, NARASIMHAN D, et al. Rapid densification of porous carbon-carbon composites by thermal-gradient chemical vapor infiltration[J]. Applied Physics Letters, 1995, 66(18):2334-2336. [18] 清华大学.一种基于CVD/CVI双工艺的纤维增强复合材料沉积炉:CN212270232U[P]. 2021-01-01. TSINGHUA UNIVERSITY. Fiber reinforced composite material deposition furnace based on CVD/CVI double process:CN212270232U[P]. 2021-01-01.(in Chinese) [19] ALBRIGHT L F. Albright's chemical engineering handbook[M]. Boca Raton:CRC Press, 2008. [20] GEORGIADIS J G, CATTON I. An effective equation governing convective transport in porous media[J]. Journal of Heat Transfer, 1988, 110(3):635-641. [21] ERGUN S. Fluid flow through packed columns[J]. Chemical Engineering Progress, 1952, 48(2):89-94. [22] MOALLEMI M K, ZHANG H, KUMAR S. Numerical modeling of two-dimensional smoldering processes[J]. Combustion and Flame, 1993, 95(1-2):170-182. [23] PANDEY A, SELVAM P, DHINDAW B K, et al. Multiscale modeling of chemical vapor infiltration process for manufacturing of carbon-carbon composite[J]. Materials Today:Proceedings, 2020, 21:1059-1063. [24] COMSOL, INC. Heat transfer module user's guide. version:COMSOL 5.4[R/OL].(2018-09-27)[2022-10-11] . https://doc.comsol.com/5.4/doc/com.comsol.help.heat/HeatTransferModuleUsersGuide.pdf. [25] NIELD D A, BEJAN A. Convection in porous media[M]. New York:Springer, 2013. [26] HUA Y F, ZHANG L T, CHENG L F, et al. A two-process model for study of the effect of fiber preform structure on isothermal chemical vapor infiltration of silicon carbide matrix composites[J]. Computational Materials Science, 2009, 46(1):133-141. [27] 魏玺.碳化硅陶瓷基复合材料ICVI过程的计算机模拟研究[D].西安:西北工业大学, 2006. WEI X. Computational simulation of ICVI process of silicon carbide ceramic matrix composites[D]. Xi'an:Northwestern Polytechnical University, 2006.(in Chinese) [28] MCALLISTER P, WOLF E E. Modeling of chemical vapor infiltration of carbon in porous carbon substrates[J]. Carbon, 1991, 29(3):387-396. [29] SHELDON B W, BESMANN T M. Reaction and diffusion kinetics during the initial stages of isothermal chemical vapor infiltration[J]. Journal of the American Ceramic Society, 1991, 74(12):3046-3053. [30] STARR T L. Gas transport model for chemical vapor infiltration[J]. Journal of Materials Research, 1995, 10(9):2360-2366.
2023, Vol. 63 
