| MECHANICAL ENGINEERING |
|
|
|
|
|
Tribological properties of overlap and non-overlap zones in laser-clad iron-based coatings |
| WU Ying1,2, LIU Yan1, CHEN Wenjing3, CHEN Hui1 |
1. School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu 610031, China;
2. Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China;
3. School of Materials Science and Engineering, Xihua University, Chengdu 610039, China |
|
|
|
|
Abstract The microstructures of multi-pass laser cladding coatings exhibit periodic changes that are generally divided into overlap and non-overlap zones. The tribological properties of these two zones were studied using linear reciprocating friction tests with forces of 5 and 25 N and friction times of 150 and 300 s. This study analyzed the tribological characteristics with analyses of the microstructures and phases in the two zones. The results show the relationship between the tribological effects and the microstructure and the evolution of the microstructure during the friction process. The results show that at low pressures, the anti-wear characteristics are greatly affected by the microstructure. The overlap zone has poor wear resistance due to the coarse microstructure and less α-Fe content while the non-overlap zone with a finer microstructure and high α-Fe content has better wear resistance. At high pressures, the wear characteristics are less affected by the microstructure with the anti-wear characteristics of the overlap zone being similar to those of the non-overlap zone. The subsurface below the wear scar had a shear deformation layer after the friction test whose thickness, hardness and equivalent strain increased with increasing pressure and friction time. The overlap zone hardness increases faster than that of the non-overlap zone.
|
| Keywords
multi-pass laser cladding
overlap and non-overlap zones
microstructure
tribological properties
|
|
Issue Date: 10 March 2022
|
|
|
[1] 黄勇, 孙文磊, 周超军, 等. 基于激光熔覆的再制造零件可视化损伤修复区域规划[J]. 焊接学报, 2017, 38(11):51-56.HUANG Y, SUN W L, ZHOU C J, et al. Planning of repair area of visual damage on component to be remanufactured by laser cladding[J]. Transactions of the China Welding Institution, 2017, 38(11):51-56. (in Chinese)(查阅所有网上资料, 未找到对应的英文翻译, 请联系作者确认)
[2] WANG D Z, HU Q W, ZHENG Y L, et al. Study on deposition rate and laser energy efficiency of laser-induction hybrid cladding[J]. Optics & Laser Technology, 2016, 77:16-22.
[3] LI K B, LI D, LIU D Y, et al. Microstructure evolution and mechanical properties of multiple-layer laser cladding coating of 308L stainless steel[J]. Applied Surface Science, 2015, 340:143-150.
[4] ZHANG K, WANG S J, LIU W J, et al. Characterization of stainless steel parts by laser metal deposition shaping[J]. Materials & Design, 2014, 55:104-119.
[5] XU G J, KUTSUNA M, LIU Z J, et al. Characteristic behaviours of clad layer by a multi-layer laser cladding with powder mixture of Stellite-6 and tungsten carbide[J]. Surface and Coatings Technology, 2006, 201(6):3385-3392.
[6] WANG Q Y, PEI R, LIU S, et al. Microstructure and corrosion behavior of different clad zones in multi-track Ni-based laser-clad coating[J]. Surface and Coatings Technology, 2020, 402:126310.
[7] ZHANG P L, LIU X P, LU Y L, et al. Microstructure and wear behavior of Cu-Mo-Si coatings by laser cladding[J]. Applied Surface Science, 2014, 311:709-714.
[8] 赵龙志, 邓楚祥, 王震, 等. Ti含量对Fe-Ni-Ti激光熔覆层摩擦性能的影响[J]. 表面技术, 2020, 49(10):39-44, 98.ZHAO L Z, DENG C X, WANG Z, et al. Effect of Ti content on tribology properties of Fe-Ni-Ti laser cladding[J]. Surface Technology, 2020, 49(10):39-44, 98. (in Chinese)
[9] 李珂尧, 周健松, 王凌倩. B、Si元素对激光熔覆Fe-Cr-Mo-B-Si非晶涂层的非晶形成能力及其摩擦学机理的影响[J]. 表面技术, 2020, 49(8):192-202. LI K Y, ZHOU J S, WANG L Q. Effect of B and Si elements on the amorphous formation ability and tribological mechanism of Fe-Cr-Mo-B-Si amorphous coatings by laser cladding[J]. Surface Technology, 2020, 49(8):192-202. (in Chinese)
[10] 吉政甲, 勒洪允, 骆晚玥, 等.造粒氧化锆增强复合材料的摩擦学性能及优化[J]. 清华大学学报(自然科学版), 2020, 60(8):639-647.JI Z J, JIN H Y, LUO W Y, et al. Optimization of the tribological characteristics of lubricant materials with granulated ZrO2[J]. Journal of Tsinghua University (Science and Technology), 2020, 60(8):639-647. (in Chinese)
[11] LIN X, YUE T M, YANG H O, et al. Laser rapid forming of SS316L/Rene88DT graded material[J]. Materials Science and Engineering:A, 2005, 391(1-2):325-336.
[12] TURNBULL D. Kinetics of heterogeneous nucleation[J]. Journal of Chemical Physics, 1950, 18(2):198.
[13] WANG X H, SONG S L, QU S Y, et al. Characterization of in situ synthesized TiC particle reinforced Fe-based composite coatings produced by multi-pass overlapping GTAW melting process[J]. Surface and Coatings Technology, 2007, 201(12):5899-5905.
[14] VENKATARAMAN B, SUNDARARAJAN G. The sliding wear behaviour of Al-SiC particulate composites-II. The characterization of subsurface deformation and correlation with wear behaviour[J]. Acta Materialia, 1996, 44(2):461-473.
[15] WASEKAR N P, HARIDOSS P, SESHADRI S K, et al. Sliding wear behavior of nanocrystalline nickel coatings:Influence of grain size[J]. Wear, 2012, 296(1-2):536-546.
[16] MORALES E V, POZO J A, OLAYA L, et al. Remarks on the evolution and performance of the different austenite morphologies at the simulated HAZs of a 2205 duplex stainless steel[J]. Journal of Materials Research and Technology, 2019, 8(5):3936-3949.
[17] YANG Y H, YAN B, LI J, et al. The effect of large heat input on the microstructure and corrosion behaviour of simulated heat affected zone in 2205 duplex stainless steel[J]. Corrosion Science, 2011, 53(11):3756-3763.
[18] TAO P, GONG J M, WANG Y F, et al. Characterization on stress-strain behavior of ferrite and austenite in a 2205 duplex stainless steel based on nanoindentation and finite element method[J]. Results in Physics, 2018, 11:377-384. |
|
Viewed |
|
|
|
Full text
|
|
|
|
|
Abstract
|
|
|
|
|
Cited |
|
|
|
|
| |
Shared |
|
|
|
|
| |
Discussed |
|
|
|
|
2022,
Vol. 62
