Please wait a minute...
 首页  期刊介绍 期刊订阅 联系我们
 
最新录用  |  预出版  |  当期目录  |  过刊浏览  |  阅读排行  |  下载排行  |  引用排行  |  百年期刊
Journal of Tsinghua University(Science and Technology)    2018, Vol. 58 Issue (5) : 477-481     DOI: 10.16511/j.cnki.qhdxxb.2018.25.025
MECHANICAL ENGINEERING |
Parametric adaptability of TIG arc-induced non-contact MIG arc ignition
TANG Yingying, ZHU Zhiming, YANG Zhongyu, FU Pingpo
Key Laboratory for Advanced Materials Processing Technology of Ministry of Education, Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China
Download: PDF(4668 KB)  
Export: BibTeX | EndNote | Reference Manager | ProCite | RefWorks    
Abstract  A series of arc ignition experiments using tungsten inert gas-metal inert gas (TIG-MIG) hybrid welding was conducted for various MIG welding parameters with simultaneous measurements of the arc voltage, the welding current and images of the TIG-MIG hybrid welding arc. These experiments studied the characteristics of the TIG arc-induced non-contact MIG arc ignition and its adaptability to the various MIG welding parameters. The results show that the initial TIG arc not only quickly enables the MIG welding to achieve non-contact arc ignition but also enables the MIG welding to enter a stable droplet-free transfer mode with a relatively low arc voltage and welding current. The weld appearance is more uniform than the conventional MIG welding with no spatter. The initial wire feed speed, welding torch inclination angle, shield gas flow rate and welding wire end diameter for the MIG welding could be varied over relatively wide ranges with non-contact arc ignition of the MIG welding when ignited by the TIG arc. If the initial wire feed speed is properly matched to the welding wire end diameter, no spatter is produced during the non-contact MIG arc ignition process even with large residual droplet on the end of the welding wire.
Keywords metal inert gas (MIG) welding      non-contact arc ignition      arc ignition reliability      welding spatter      initial wire feed speed      welding wire end diameter     
ZTFLH:  TG403  
Issue Date: 15 May 2018
Service
E-mail this article
E-mail Alert
RSS
Articles by authors
TANG Yingying
ZHU Zhiming
YANG Zhongyu
FU Pingpo
Cite this article:   
TANG Yingying,ZHU Zhiming,YANG Zhongyu, et al. Parametric adaptability of TIG arc-induced non-contact MIG arc ignition[J]. Journal of Tsinghua University(Science and Technology), 2018, 58(5): 477-481.
URL:  
http://jst.tsinghuajournals.com/EN/10.16511/j.cnki.qhdxxb.2018.25.025     OR     http://jst.tsinghuajournals.com/EN/Y2018/V58/I5/477
  
  
  
  
  
  
  
  
  
[1] ERSOY U, HU S J, KANNATEY-ASIBU E. Observation of arc start instability and spatter generation in GMAW[J]. Welding Journal, 2008, 87(2):51-56.
[2] MITA T. Spatter reduction-power source considerations[J]. Welding International, 1991, 5(11):847-850.
[3] STAVA E K. The surface-tension-transfer power source:A new low-spatter arc welding machine[J]. Welding Journal, 1993, 72(1):25-29.
[4] 杨修荣. 超薄板的MIG/MAG焊-CMT冷金属过渡技术[J]. 电焊机, 2006, 36(6):5-7.YANG X R. CMT cold metal transfer process[J]. Electric Welding Machine, 2006, 36(6):5-7. (in Chinese)
[5] 刚铁, 殷树言, 王克鸿, 等. 微机控制脉冲MIG焊引弧及收弧的研究[J]. 焊接, 1992(10):12-17. GANG T, YIN S Y, WANG K H, et al. Arc striking and ending of pulse MIG process controlled by MC[J]. Welding & Joining, 1992(10):12-17. (in Chinese)
[6] DOS SANTOS T F, DUTRA J C. Arc initiation in aluminium GMAW[J]. Welding International, 2010, 24(11):817-824.
[7] ERA T, IDE A, UEZONO T, et al. Spatter reduction in GMAW of stainless steel sheets using CBT process[J]. Welding International, 2013, 27(4):274-280.
[8] CHEN J H, SUN Z C, FAN D. Study of the mechanism of spatter produced by basic welding electrodes[J]. Welding Journal, 1996, 75(10):311-316.
[9] 娄小飞, 陈茂爱, 武传松, 等. 高速TIG-MIG复合焊焊缝驼峰及咬边消除机理[J]. 焊接学报, 2014, 35(8):87-90. LOU X F, CHEN M A, WU C S, et al. Humping and undercutting suppression mechanism for high speed TIG-MIG hybrid welding[J]. Transactions of the China Welding Institution, 2014, 35(8):87-90. (in Chinese)
[10] CHEN J, ZONG R, WU C S, et al. Influence of low current auxiliary TIG arc on high speed TIG-MIG hybrid welding[J]. Journal of Materials Processing Technology, 2017, 243:131-142.
[11] KANEMARU S, SASAKI T, SATO T, et al. Study for TIG-MIG hybrid welding process[J]. Welding in the World, 2014, 58(1):11-18.
[12] KANEMARU S, SASAKI T, SATO T, et al. Study for the mechanism of TIG-MIG hybrid welding process[J]. Welding in the World, 2015, 59(2):261-268.
[13] 王世博. 铝合金TIG-MIG复合焊电弧行为及熔滴过渡研究[D]. 哈尔滨:哈尔滨工业大学, 2016. WANG S B. Research on arc beheviour and metal transfer of TIG-MIG hybrid arc welding for aluminum alloy[D]. Harbin:Harbin Institute of Technology, 2016. (in Chinese)
[14] DING M, LIU S S, ZHENG Y, et al. TIG-MIG hybrid welding of ferritic stainless steels and magnesium alloys with Cu interlayer of different thickness[J]. Materials & Design, 2015, 88:375-383.
[1] ZHU Zhiming, FAN Kaiguo, LIU Han, WANG Yongdong. Influence of low atmospheric pressures on the arc characteristics of self-shielded flux-core wire[J]. Journal of Tsinghua University(Science and Technology), 2015, 55(7): 734-738.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
Copyright © Journal of Tsinghua University(Science and Technology), All Rights Reserved.
Powered by Beijing Magtech Co. Ltd