Parametric adaptability of TIG arc-induced non-contact MIG arc ignition

TANG Yingying; ZHU Zhiming; YANG Zhongyu; FU Pingpo

doi:10.16511/j.cnki.qhdxxb.2018.25.025

PDF(4668 KB)

Journal of Tsinghua University(Science and Technology) ›› 2018, Vol. 58 ›› Issue (5) : 477-481. DOI: 10.16511/j.cnki.qhdxxb.2018.25.025

MECHANICAL ENGINEERING

Parametric adaptability of TIG arc-induced non-contact MIG arc ignition

{{article.zuoZhe_EN}}

Author information +

History +

Abstract

A series of arc ignition experiments using tungsten inert gas-metal inert gas (TIG-MIG) hybrid welding was conducted for various MIG welding parameters with simultaneous measurements of the arc voltage, the welding current and images of the TIG-MIG hybrid welding arc. These experiments studied the characteristics of the TIG arc-induced non-contact MIG arc ignition and its adaptability to the various MIG welding parameters. The results show that the initial TIG arc not only quickly enables the MIG welding to achieve non-contact arc ignition but also enables the MIG welding to enter a stable droplet-free transfer mode with a relatively low arc voltage and welding current. The weld appearance is more uniform than the conventional MIG welding with no spatter. The initial wire feed speed, welding torch inclination angle, shield gas flow rate and welding wire end diameter for the MIG welding could be varied over relatively wide ranges with non-contact arc ignition of the MIG welding when ignited by the TIG arc. If the initial wire feed speed is properly matched to the welding wire end diameter, no spatter is produced during the non-contact MIG arc ignition process even with large residual droplet on the end of the welding wire.

Key words

metal inert gas (MIG) welding / non-contact arc ignition / arc ignition reliability / welding spatter / initial wire feed speed / welding wire end diameter

Cite this article

EndNote

Ris (Procite)

Bibtex

Download Citations

TANG Yingying, ZHU Zhiming, YANG Zhongyu, FU Pingpo. Parametric adaptability of TIG arc-induced non-contact MIG arc ignition[J]. Journal of Tsinghua University(Science and Technology). 2018, 58(5): 477-481 https://doi.org/10.16511/j.cnki.qhdxxb.2018.25.025

References

[1] ERSOY U, HU S J, KANNATEY-ASIBU E. Observation of arc start instability and spatter generation in GMAW[J]. Welding Journal, 2008, 87(2):51-56.
[2] MITA T. Spatter reduction-power source considerations[J]. Welding International, 1991, 5(11):847-850.
[3] STAVA E K. The surface-tension-transfer power source:A new low-spatter arc welding machine[J]. Welding Journal, 1993, 72(1):25-29.
[4] 杨修荣. 超薄板的MIG/MAG焊-CMT冷金属过渡技术[J]. 电焊机, 2006, 36(6):5-7.YANG X R. CMT cold metal transfer process[J]. Electric Welding Machine, 2006, 36(6):5-7. (in Chinese)
[5] 刚铁, 殷树言, 王克鸿, 等. 微机控制脉冲MIG焊引弧及收弧的研究[J]. 焊接, 1992(10):12-17. GANG T, YIN S Y, WANG K H, et al. Arc striking and ending of pulse MIG process controlled by MC[J]. Welding & Joining, 1992(10):12-17. (in Chinese)
[6] DOS SANTOS T F, DUTRA J C. Arc initiation in aluminium GMAW[J]. Welding International, 2010, 24(11):817-824.
[7] ERA T, IDE A, UEZONO T, et al. Spatter reduction in GMAW of stainless steel sheets using CBT process[J]. Welding International, 2013, 27(4):274-280.
[8] CHEN J H, SUN Z C, FAN D. Study of the mechanism of spatter produced by basic welding electrodes[J]. Welding Journal, 1996, 75(10):311-316.
[9] 娄小飞, 陈茂爱, 武传松, 等. 高速TIG-MIG复合焊焊缝驼峰及咬边消除机理[J]. 焊接学报, 2014, 35(8):87-90. LOU X F, CHEN M A, WU C S, et al. Humping and undercutting suppression mechanism for high speed TIG-MIG hybrid welding[J]. Transactions of the China Welding Institution, 2014, 35(8):87-90. (in Chinese)
[10] CHEN J, ZONG R, WU C S, et al. Influence of low current auxiliary TIG arc on high speed TIG-MIG hybrid welding[J]. Journal of Materials Processing Technology, 2017, 243:131-142.
[11] KANEMARU S, SASAKI T, SATO T, et al. Study for TIG-MIG hybrid welding process[J]. Welding in the World, 2014, 58(1):11-18.
[12] KANEMARU S, SASAKI T, SATO T, et al. Study for the mechanism of TIG-MIG hybrid welding process[J]. Welding in the World, 2015, 59(2):261-268.
[13] 王世博. 铝合金TIG-MIG复合焊电弧行为及熔滴过渡研究[D]. 哈尔滨:哈尔滨工业大学, 2016. WANG S B. Research on arc beheviour and metal transfer of TIG-MIG hybrid arc welding for aluminum alloy[D]. Harbin:Harbin Institute of Technology, 2016. (in Chinese)
[14] DING M, LIU S S, ZHENG Y, et al. TIG-MIG hybrid welding of ferritic stainless steels and magnesium alloys with Cu interlayer of different thickness[J]. Materials & Design, 2015, 88:375-383.