作为汽车轻量化的重要材料，铝合金的脆性断裂问题不可忽视。该文以某汽车铝型材防撞梁为研究对象，开展了铝合金静态和动态拉伸、静态剪切、静态缺口、静态拉剪以及穿孔等力学性能试验，获取了铝合金材料在不同应变率下拉伸应力状态的力学特性，以及准静态拉压剪等不同应力状态下的力学属性数据，使用Swift-Hockett-Sherby本构描述铝合金材料应变硬化特性，基于LS-DYNA有限元法模拟对标拉压剪等不同应力状态试验，获得不同应力状态试验的失效单元的应力三轴度和Lode角信息，标定了铝合金材料的修正的 Mohr-Coulomb（MMC）断裂准则。通过铝型材动态三点弯结构试验和模拟，验证了MMC断裂模型对于表征铝合金材料在不同应力状态下断裂失效的有效性。
Aluminum alloys are important light materials for vehicle weight reduction, but they frequently experience fracture under impact loading. This paper describes experimental and analytical methods for characterizing the fracture of aluminum alloy bumper beams. A test matrix is designed to obtain the material mechanical properties at different tensile strain rates and a variety of stress states, including tension, shear, notch tension, tension-shear and punch. The Swift-Hockett-Sherby law is used to describe the hardening of the material, with different stress states then simulated in the LS-DYNA finite element analysis environment to get a good correlation. Then, the stress triaxialities and lode angles extracted from the simulations are used to calibrate a modified Mohr-Coulomb (MMC) fracture model. Simulations of the material tests and a component bending test with the MMC model correlate well with the test results to support the validity of this method for fracture characterization, as well as the validity of the MMC fracture model for predicting metal fracture.
[1] 姚付彬. CR590T/340Y DP镀锌钢板点焊接头组织和性能的研究[D]. 长春: 吉林大学, 2011.YAO Fubin. Study on Microstructures and Properties of Ressistance Spot-Welded Joints of Galvanized Steel Sheets with Trademark of CR590T/340Y DP [D]. Changchun: Jilin University, 2011. (in Chinese) [2] 宫林松, 童胜坤, 唐良文, 等. A356.2 铝合金轮毂拉伸性能及断口分析[J]. 汽车工艺与材料, 2012(10): 42-46.GONG Linsong, TONG Shengkun, TANG Liangwen, et al. A356.2 aluminum alloy wheel hub tensile properties and fracture analysis [J]. Automobile Technology & Material, 2012(10): 42-46. (in Chinese) [3] 吕丹, 朱亮, 朱浩, 等. 不同应力状态下6061铝合金力学性能及断裂行为的研究[J]. 轻合金加工技术, 2010, 38(4): 52-55.LÜ Dan, ZHU Liang, ZHU Hao, et al. Study of mechanics property and fracture behaviors on 6061 aluminum alloy under different stress states [J]. Light Alloy Fabrication Technology, 2010, 38(4): 52-55. (in Chinese) [4] 冯伟明, 许庆彦, 柳百成, 等. 铝合金微观组织模拟及并行计算[J]. 清华大学学报 (自然科学版), 2003, 43(5): 605-608.FENG Weiming, XU Qingyan, LIU Baicheng, et al. Microstructure simulation of aluminum alloy using parallel processors [J]. J Tsinghua Univ (Sci & Tech), 2003, 43(5): 605-608. (in Chinese) [5] Zhang T, Fang E, Liu P, et al. Modeling and simulation of 2012 Sandia fracture challenge problem: Phantom paired shell for Abaqus and plane strain core approach [J]. International Journal of Fracture, 2013, 186: 117-139. [6] 朱浩. 车用铝合金变形损伤和断裂机理研究与材料表征及有限元模拟[D]. 兰州: 兰州理工大学, 2008.ZHU Hao. Study on Deformation Mechanism of Damage and Fracture of Aluminum Alloy and Material Characterization and Finite Element Simulation [D]. Lanzhou: Lanzhou University of Technology, 2008. (in Chinese) [7] Bai Y, Wierzbicki T. Application of extended Mohr-Coulomb criterion to ductile fracture [J]. International Journal of Plasticity, 2010, 161: 1-20. [8] Algarni M, Bai Y, Choi Y. A study of Inconel 718 dependency on stress triaxiality and Lode angle in plastic deformation and ductile fracture [J]. Engineering Fracture Mechanics, 2015, 147: 140-157. [9] Pack K, Luo M, Wierzbicki T. Sandia fracture challenge: Blind prediction and full calibration to enhance the fracture predictability [J]. International Journal of Fracture, 2014, 186(2): 155-175. [10] Huang G, Zhu H, Sriram S. Fracture prediction and correlation of ALSI hot stamped steels with different models in LS-DYNA(R) [C]//13th International LS-DYNA Users Conference 2014. Dearborn, MI, 2014. [11] Bai Y, Wierzbicki T. A comparative study of three groups of ductile fracture loci in the 3D space [J]. Engineering Fracture Mechanics, 2015, 135: 147–167. [12] 高付海, 桂良进, 范子杰. 两种新型单拉平板剪切试件的设计与对比[J]. 清华大学学报 (自然科学版), 2010, 50(2): 299-302.GAO Fuhai, GUI Liangjin, FAN Zijie. Design and comparison of two new in-plane shear specimens [J]. J Tsinghua Univ (Sci & Tech), 2010, 50(2): 299-302. (in Chinese) [13] 朱俊儿, 孟艳, 罗海灵, 等. 一种针对颈缩现象的高强钢板材力学行为研究方法[J]. 北京理工大学学报, 2014, 34(S1): 75-78.ZHU Juner, MENG Yan, LUO Hailing, et al. A hybrid experimental-numerical converse method for the necking behaviour study of high strength steel sheets [J]. Transactions of Beijing Institute of Technology, 2014, 34(S1): 75-78. (in Chinese)
