[Objective] The optimal arrangement of large radial gates is a critical prerequisite for ensuring structural safety. The equal-load arrangement method and the approximate zero-bending-moment method are widely applied in current engineering practice. Both conventional methods neglect the influence of the spatial curvature of gate structures, leading to substantial calculation deviations for large surface outlet radial gates with distinct curved features. Taking representative two-arm and three-arm surface outlet radial gates in China as prototypes, this study optimized the zero-bending-moment arrangement method to account for spatial curvature and evaluated its effect on the zero-bending-moment arrangement coefficients with curvature, so as to provide technical support for the rational layout of large radial gates and the improvement of design specifications. [Methods] ANSYS Parametric Design Language modeling was used to establish a three-dimensional spatial frame finite element model of radial gates that enabled the geometric parameters, curvature radii, and arm positions to be varied. A double-loop iterative optimization strategy was adopted: the outer loop scanned a range of curvature radii R, and the inner loop adjusted the spatial positions of each arm. The optimization objective was to reduce the bending moment in the longitudinal plane at the arm ends to zero. Systematic finite element calculations were performed for two-arm and three-arm radial gates under different R/H ratios, where H is the gate height. Through iterative calculations, the zero-bending-moment arrangement coefficients under different spatial curvatures were obtained, and the corresponding fitting formulas were derived using nonlinear regression analysis. [Results] With increasing R/H, the zero-bending-moment arrangement coefficients for the two-arm and three-arm radial gates first increased rapidly (R/H ≤ 1.3), gradually decreased (1.3 < R/H < 1.5), and finally stabilized (R/H ≥ 1.5). Within the range recommended by current codes, there were notable differences between the equal-load and the proposed methods, with maximum discrepancies in the arrangement coefficients of 30.8% and 23.4% for two-arm and three-arm gates, respectively. The results of the approximate zero-bending-moment method matched the finite element results at low curvature, but required a correction for spatial effects at high curvature, with maximum differences of 47.9% and 40.0% for two-arm and three-arm gates, respectively. Engineering case analyses demonstrated that the proposed method improved the internal force distribution, reduced controlling stresses and displacements, and enhanced the overall stability and load-bearing capacity of gate structures. [Conclusions] Spatial curvature is a non-negligible factor in the arrangement design of large surface outlet radial gates, and traditional modeling methods that ignore curvature produce large errors for high-curvature gates. A three-stage variation in the zero-bending-moment arrangement coefficients with R/H is identified, and the critical curvature intervals are quantified. The proposed zero-bending-moment method overcomes the limitations of conventional methods, determines optimal arm positions accurately, and improves the mechanical performance of gate structures. The research results provide a valuable reference for the rational arrangement of large-span radial gates and the revision of relevant design codes.
Key words
surface outlet radial gate /
optimal structural layout /
zero bending moment of support arm end /
finite element method /
double nonlinearity
{{custom_sec.title}}
{{custom_sec.title}}
{{custom_sec.content}}
References
[1] 王正中, 张雪才, 刘计良. 大型水工钢闸门的研究进展及发展趋势[J]. 水力发电学报, 2017, 36(10): 1-18. WANG Z Z, ZHANG X C, LIU J L. Advances and developing trends in research of large hydraulicsteel gates[J]. Journal of Hydroelectric Engineering, 2017, 36(10): 1-18. (in Chinese)
[2] 李庆斌, 马睿, 胡昱, 等. 大坝智能建造研究进展与发展趋势[J]. 清华大学学报(自然科学版), 2022, 62(8):1252-1269. LI Q B, MA R, HU Y, et al. A review of intelligent dam construction techniques[J]. Journal of Tsinghua University (Science and Technology), 2022, 62(8): 1252-1269. (in Chinese)
[3] LIU F, XU C, LIU M, et al. Insights into the vibration characteristics of spatial radial gate affected by fluid-structure interaction[J]. Journal of Marine Science and Engineering, 2024, 12(10): 1804.
[4] LU X D, LIU Y K, TAN S L, et al. Study on the fluctuating load characteristics of the submerged radial gate in the high-head flood discharge outlet[J]. Applied Sciences, 2024, 14(17): 7470.
[5] 刘计良, 王正中, 刘云贺, 等. 关于在规范中增加“横向三支臂”弧形闸门的建议[J]. 水力发电, 2023, 49(12): 81-88. LIU J L, WANG Z Z, LIU Y H, et al. Suggestion on adding transverse three-arm radial gate in the design code[J]. Water Power, 2023, 49(12): 81-88. (in Chinese)
[6] 中华人民共和国水利部. 水利水电工程钢闸门设计规范: SL 74-2019[S]. 北京: 中国水利水电出版社, 2020. Ministry of Water Resources of the People's Republic of China. Design specification for steel gates of water and hydropower projects: SL 74-2019[S]. Beijing: China Water & Power Press, 2020. (in Chinese)
[7] 国家能源局. 水电工程钢闸门设计规范: NB 35055—2015[S]. 北京: 中国电力出版社, 2016. National Energy Administration. Design code for steel gate in hydropower projects: NB 35055—2015[S]. Beijing: China Electric Power Press, 2016. (in Chinese)
[8] 王正中, 李宗利, 娄宗科. 三支臂表孔弧门合理结构布置[J]. 西北农业大学学报, 1995, 23(3): 230-233. WANG Z Z, LI Z L, LOU Z K. Rational structural arrangement of three-arm table-hole arc gates[J]. Journal of Northwest A&F University, 1995, 23(3): 230-233. (in Chinese)
[9] 王正中. 关于大中型弧形钢闸门合理结构布置及计算图式的探讨[J]. 人民长江, 1995, 26(1): 54-59. WANG Z Z. Discussion on the rational structural arrangement and calculation schemes for large and medium-sized curved steel gates[J]. Yangtze River, 1995, 26(1):54-59. (in Chinese)
[10] 刘计良, 王正中, 贾仕开. 基于合理布置的三支臂弧门主框架优化设计[J]. 浙江大学学报(工学版), 2011, 45(11): 1985-1990. LIU J L, WANG Z Z, JIA S K. Optimization design of main frame of radial gate with three arms based on rational layout[J]. Journal of Zhejiang University (Engineering Science), 2011, 45(11): 1985-1990. (in Chinese)
[11] 张雪才, 谢遵党, 陈丽晔, 等. 弧形钢闸门纵向框架结构合理布置研究[J]. 华中科技大学学报(自然科学版), 2021, 49(11): 101-106. ZHANG X C, XIE Z D, CHEN L Y, et al. Study on reasonable layout of longitudinal frame structure of radial steel gate[J]. Journal of Huazhong University of Science and Technology (Natural Science Edition), 2021, 49(11): 101-106. (in Chinese)
[12] 殷有泉, 邸元, 姚再兴. 非线性有限元方程组的弧长延拓算法[J]. 北京大学学报(自然科学版), 2017, 53(5): 793-800. YIN Y Q, DI Y, YAO Z X. Arc-Length continuation algorithm for nonlinear finite element equations[J]. Acta Scientiarum Naturalium Universitatis Pekinensis, 2017, 53(5): 793-800. (in Chinese)
[13] 叶继红, 许强. 基于杆系离散元理论的结构屈曲显式弧长法研究[J]. 工程力学, 2024, 41(3): 9-18. YE J H, XU Q. An explicit arc-length method for structural bucklinganalysis based on member discrete element theory[J]. Engineering Mechanics, 2024, 41(3): 9-18. (in Chinese)
[14] TANGBANJONGKIJ C, CHUCHEEPSAKUL S, PULNGERN T, et al. Effects of circumferential weld-induced imperfections on the buckling behavior of fabricated steel toroidal shells[J]. Nuclear Engineering and Design, 2024, 418: 112913.
[15] WALPORT F, CHAN H U, NETHERCOT D A, et al. Design of stainless steel structural systems by GMNIA with strain limits[J]. Engineering Structures, 2023, 276: 115339.
[16] 廖明进, 范可征, 徐宇. 内置预应力钢绞线的分片式钢混塔筒的非线性力学响应[J]. 清华大学学报(自然科学版), 2025, 65(8): 1583-1595. LIAO M J, FAN K Z, XU Y. Nonlinear mechanical response of prestressed segmented steel-concrete towers[J]. Journal of Tsinghua University (Science and Technology), 2025, 65(8): 1583-1595. (in Chinese)
[17] CHAN H U, WALPORT F, SLACK H, et al. Practical rules for defining initial geometric imperfections for in-plane stability design of steel frames[J]. Structures, 2025, 82: 110643.
[18] QUAN C Y, WALPORT F, GARDNER L. Equivalent geometric imperfections for the design of steel and stainless steel beam-columns by GMNIA[J]. Journal of Constructional Steel Research, 2024, 215:108502.
[19] RADWAN M, KÖVESDI B. Equivalent geometric imperfection for interaction buckling of welded box-section columns-Stochastic analysis[J]. Journal of Constructional Steel Research, 2024, 213: 108374.
[20] 李胜首, 罗文贵, 马济阳, 等. 考虑初始缺陷下的加劲压力钢管稳定性分析[J]. 水电能源科学, 2025, 43(11): 177-181. LI S S, LUO W G, MA J Y, et al. Stability analysis of stiffened pressure steel pipes considering initial imperfections[J]. Water Resources and Power, 2025, 43(11): 177-181. (in Chinese)
[21] HUANG S X, QIAO P Z, LU L J, et al. Nonlinear stability analysis of rotationally-restrained imperfect doubly curved composite shallow shells[J]. Thin-Walled Structures, 2019, 142: 358-368.
[22] 中华人民共和国住房和城乡建设部, 中华人民共和国国家质量监督检验检疫总局. 钢结构设计标准:GB50017-2017[S]. 北京: 中国建筑工业出版社, 2017. Ministry of Housing and Urban-Rural Development of the People's Republic of China, General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China. Standard for design of steel structures: GB 50017-2017[S]. Beijing: China Architecture & Building Press, 2017. (in Chinese)