[Objective] A centrifugal compressor is a key equipment in the gas diffusion isotope separation cascade at pressures below 5 000 Pa, and its performance affects the economics of the separation cascade. Currently, only a few studies have focused on the performance and internal flow characteristics of centrifugal compressors under negative pressure conditions (inlet pressure ≤101 325 Pa), especially when the inlet pressure is as low as 400 Pa. Additionally, in our experiments with the designed centrifugal compressor, an increase in inlet pressure improved the pressure ratio for the same inlet volume flow rate. Therefore, investigating the impact of the inlet pressure on the performance of centrifugal compressors is necessary. [Methods] Taking the Krain centrifugal impeller as the research object, the finite volume method is used to solve the three-dimensional Reynolds time-averaged Navier-Stokes (RANS) equations, and the ideal gas state and Spalart-Allmaras turbulence model equations are substituted into the RANS equations. A single flow channel calculation model, including the inducer, impeller, and vaneless diffuser, is meshed by 1.88 million hexahedral structural grids. The thickness of the first layer of the grid near the walls is 6 μm, and the y+ value in most calculation domains is set to be less 10, satisfying the grid independence verification. The boundary conditions are as follows: total pressure, total temperature, and velocity along the axis direction are given at the inlet, while the mass flow rate is provided at the outlet; all walls are no-slip adiabatic boundaries. The relative deviation between the calculated values of the verification case and experimental values is approximately 3%, indicating the accuracy and reliability of the calculation method. [Results] The numerical results were summarized as follows. (1) As the inlet pressure decreased, the total pressure ratio and total isentropic efficiency of the compressor first decreased slowly and then decreased rapidly. When the pressure was 400 Pa, performance was reduced by 10% compared with that at 101 325 Pa, and the range of stable operating conditions decreased. (2) The specific entropy increase in the compressor components gradually increased with decreasing inlet pressure, implying that the specific flow loss was improved. Among them, the specific entropy increase in the vaneless diffuser increased faster than the two other components. (3) The distribution of the specific entropy increase revealed that the decrease in the inlet pressure reinforced backflow and secondary flow losses at the impeller outlet, as well as boundary layer lossed on the hub and shroud side of the diffuser. (4) The flow characteristics showed that when the inlet pressure decreased to 400 Pa, the backflow velocity at the impeller outlet increased, and the backflow region expanded. In the vaneless diffuser, as the inlet pressure decreased, the gradient of the radial velocity on the hub side and that of tangential velocity on the hub and shroud sides decreased, indicating a thicker boundary layer. [Conclusions] The decrease in the inlet pressure increases the thickness of the boundary layer on the hub side of the vaneless diffuser and enhances backflow and secondary flow at the impeller outlet, increasing the boundary layer, backflow, and secondary flow losses and subsequently decreasing compressor performance. Therefore, during the initial design stage of negative-pressure centrifugal compressors, performance predicted using a one-dimensional performance model based on positive pressure is high and needs to be corrected.
HUANG Dongyang
,
ZHOU Wenbi
,
JIANG Dongjun
,
PAN Jianxiong
. Numerical study on the effect of the inlet pressure on centrifugal compressor performance[J]. Journal of Tsinghua University(Science and Technology), 2024
, 64(9)
: 1666
-1676
.
DOI: 10.16511/j.cnki.qhdxxb.2024.26.041
[1] 徐忠.离心式压缩机原理[M].北京:机械工业出版社, 1990. XU Z. The principle of centrifugal compressor[M]. Beijing:China Machine Press, 1990.(in Chinese)
[2] 祁大同.离心式压缩机原理[M].北京:机械工业出版社, 2018. QI D T. The principle of centrifugal compressor[M]. Beijing:China Machine Press, 2018.(in Chinese)
[3] ECKARDT D. Detailed flow investigations within a high-speed centrifugal compressor impeller[J]. Journal of Fluids Engineering, 1976, 98(3):390-3399.
[4] JOHNSON M W, MOORE J. The development of wake flow in a centrifugal impeller[J]. Journal of Engineering for Power, 1980, 102(2):382-389.
[5] KRAIN H. Swirling impeller flow[J]. Journal of Turbomachinery, 1988, 110(1):122-128.
[6] KRAIN H, HOFFMAN W. Verification of an impeller design by laser measurements and 3D-viscous flow calculations[C]//Proceedings of the ASME 1989 International Gas Turbine and Aeroengine Congress and Exposition. Toronto, Canada:ASME, 1989:89-GT-159.
[7] 孙志刚.离心压气机内部流动特性与流场结构研究[D].北京:中国科学院研究生院(工程热物理研究所), 2011. SUN Z G. Investigation on the flow features and flowfield structures of centrifugal compressors[D]. Beijing:Insititute of Engineering Thermophysics, Chinese Academy of Sciences, 2011.(in Chinese)
[8] DEAN R C JR, SENOO Y. Rotating wakes in vaneless diffusers[J]. Journal of Fluids Engineering, 1960, 82(3):563-570.
[9] PINARBASI A, JOHNSON M. Detailed flow measurements in a centrifugal compressor vaneless diffuser[J]. Journal of Turbomachinery, 1994, 116(3):453-460.
[10] NIKIFOROV A, AVRAMENKO D, KUCHUMOV A, et al. Vaneless diffusers characteristics simulating by means of neural networks[J]. IOP Conference Series:Materials Science and Engineering, 2019, 604:012046.
[11] KRAIN H. A study on centrifugal impeller and diffuser flow[J]. Journal of Engineering for Power, 1981, 103(4):688-697.
[12] ZIEGLER K U, GALLUS H E, NIEHUIS R. A study on impeller-diffuser interaction. Part I:Influence on the performance[J]. Journal of Turbomachinery, 2003, 125(1):173-182.
[13] 顾承真,闵兆升,洪厚胜.机械蒸汽再压缩蒸发系统的性能分析[J].化工进展, 2014, 33(1):30-35. GU C Z, MIN Z S, HONG H S. Performance analysis of mechanical vapor recompression evaporation system[J]. Chemical Industry and Engineering Progress, 2014, 33(1):30-35.(in Chinese)
[14] 薛芳,苏秀平,王林忠. R1233zd (E)在离心式冷水机组中的应用研究[J].制冷与空调, 2019, 19(2):24-9. XUE F, SU X P, WANG L Z. Application study of R1233zd (E) into centrifugal chiller[J]. Refrigeration and Air-Condtioning, 2019, 19(2):24-9.(in Chinese)
[15] 周明胜,裴根,姜东君,等.用于负压条件下的高速磁悬浮压缩机:CN209510664U[P]. 2019-10-18. ZHOU M S, PEI G, JIANG D J, et al. High-speed magnetic levitation centrifugal compressor for negative pressure conditions:CN209510664U[P]. 2019-10-18.(in Chinese)
[16] 席光.关于Krain实验叶轮几何型线及其流道二次流旋涡结构的讨论[J].工程热物理学报, 2000, 21(4):440-442. XI G. Discussion on the geometry and the secondary flow vortex structure of Krain's experimental compressor impeller[J]. Journal of Engineering Thermophysics, 2000, 21(4):440-442.(in Chinese)
[17] 吴其芬,陈伟芳,黄琳,等.稀薄气体动力学[M].长沙:国防科技大学出版社, 2004. WU Q F, CHEN W F, HUANG L, et al. Rare aerodynamics[M]. Changsha:National University of Defense Technology Press, 2004.(in Chinese)
[18] 张傲.离心压缩机叶片参数化造型和气动性能优化[D].大连:大连理工大学, 2022. ZHANG A. Blade parameterization and aerodynamic performance optimization of centrifugal compressor impellers[D]. Dalian:Dalian University of Technology, 2022.(in Chinese)
[19] SPALART P, ALLMARAS S. A one-equation turbulence model for aerodynamic flows[C]//Proceedings of the 30th Aerospace Sciences Meeting and Exhibit. Reno, USA:AIAA, 1992.
[20] 路倩,南希,林峰.熵产控制体方法对压气机近零间隙流动损失的演变规律[J].航空动力学报, 2016, 31(3):678-684. LU Q, NAN X, LIN F. Entropy generation control volume method and its application into flow loss evolution in a compressor with near zero tip clearance[J]. Journal of Aerospace Power, 2016, 31(3):678-684.(in Chinese)
[21] VAN ZANTE D E, TO W M, CHEN J P. Blade row interaction effects on the performance of a moderately loaded NASA transonic compressor stage[C]//Proceedings of the ASME Turbo Expo 2002:Power for Land, Sea, and Air. Amsterdam, the Netherlands:ASME, 2002.
